logo
banner

News Details

Home > News >

Company news about Ruicom GKG3 Vibration Sensor Targets Spindle Collision Detection and Tool Condition Monitoring on CNC Machine Tools

Events
CONTACT US
Mrs. Tina Chen
86--13651423792
Contact Now

Ruicom GKG3 Vibration Sensor Targets Spindle Collision Detection and Tool Condition Monitoring on CNC Machine Tools

2026-09-09
latest company news about Ruicom GKG3 Vibration Sensor Targets Spindle Collision Detection and Tool Condition Monitoring on CNC Machine Tools  0

Triaxial MEMS sensing with ±40 g range and 500 Hz bandwidth catches crash transients and chatter signatures at the source — over standard RS485 / MODBUS RTU

Ruicom today introduced the GKG3, a triaxial MEMS digital vibration sensor purpose-built for machine structure, spindle and tooling vibration monitoring. Bolted to the spindle housing and the machine column, the GKG3 streams 500 Hz-bandwidth vibration data to the CNC or the plant monitoring system over RS485 / MODBUS RTU: crash transients up to ±40 g are captured as they happen, and the chatter spectrum that warns of tool breakage is on record before the tool fails.

Why the structure knows before the controller does

A spindle crash can write off a workpiece, a tool and sometimes the spindle itself — and the machine's own protection only reacts after contact. A collision dumps a shock wave into the casting long before the drive current or the position loop reacts. A sensor mounted at the source resolves the impact transient a crash actually produces, while the same triaxial channel picks up the tooth-passing frequency and the chatter signature of a wearing tool. One sensor covers two protection jobs — with no proprietary bus required.

Vibration truth at the cutting point

  • Spindle crash & collision detection — logs the impact transient as it enters the structure, giving the controller or a safety PLC a trigger before more scrap is cut, plus a peak-g record for the post-mortem.
  • Tool wear & breakage watch — tooth-passing frequency and chatter amplitude trend inside the same 500 Hz band; a rising trend flags a dulling tool, a step jump flags a broken one.
  • Spindle bearing & gearbox health — bearing defect frequencies and gear-mesh harmonics compared against a commissioned baseline, on machines that run around the clock.
  • Plant-wide roll-out — many machines share one RS485 / MODBUS chain and one log format; where the monitoring network is IP-based, the GHA360 adds an Ethernet triaxial channel of the same measurement.

Key specifications

  • Measurement axis: X / Y / Z (triaxial)
  • Range: ±2 / ±4 / ±8 / ±10 / ±20 / ±40 g
  • Resolution @ 1 Hz: < 1 mg
  • Bandwidth (3 dB): 500 Hz
  • Noise density: 21 µg/√Hz (±2 g version)
  • Output rate: 5–1000 Hz settable
  • Interface: RS232 / RS485 / TTL · MODBUS RTU
  • Supply: DC 9–36 V · < 60 mA @ 12 V
  • Protection: IP67 aerospace aluminium · magnetic base
  • Housing / weight: 34.2 × 34.2 × 38.5 mm · ≤ 68 g

With a magnetic base, multi-point RS485 / MODBUS networking and a configurable range up to ±40 g, the GKG3 gives machine builders and plant operators a single, standard-interface sensor for both collision protection and condition-based tooling maintenance.

banner
News Details
Home > News >

Company news about-Ruicom GKG3 Vibration Sensor Targets Spindle Collision Detection and Tool Condition Monitoring on CNC Machine Tools

Ruicom GKG3 Vibration Sensor Targets Spindle Collision Detection and Tool Condition Monitoring on CNC Machine Tools

2026-09-09
latest company news about Ruicom GKG3 Vibration Sensor Targets Spindle Collision Detection and Tool Condition Monitoring on CNC Machine Tools  0

Triaxial MEMS sensing with ±40 g range and 500 Hz bandwidth catches crash transients and chatter signatures at the source — over standard RS485 / MODBUS RTU

Ruicom today introduced the GKG3, a triaxial MEMS digital vibration sensor purpose-built for machine structure, spindle and tooling vibration monitoring. Bolted to the spindle housing and the machine column, the GKG3 streams 500 Hz-bandwidth vibration data to the CNC or the plant monitoring system over RS485 / MODBUS RTU: crash transients up to ±40 g are captured as they happen, and the chatter spectrum that warns of tool breakage is on record before the tool fails.

Why the structure knows before the controller does

A spindle crash can write off a workpiece, a tool and sometimes the spindle itself — and the machine's own protection only reacts after contact. A collision dumps a shock wave into the casting long before the drive current or the position loop reacts. A sensor mounted at the source resolves the impact transient a crash actually produces, while the same triaxial channel picks up the tooth-passing frequency and the chatter signature of a wearing tool. One sensor covers two protection jobs — with no proprietary bus required.

Vibration truth at the cutting point

  • Spindle crash & collision detection — logs the impact transient as it enters the structure, giving the controller or a safety PLC a trigger before more scrap is cut, plus a peak-g record for the post-mortem.
  • Tool wear & breakage watch — tooth-passing frequency and chatter amplitude trend inside the same 500 Hz band; a rising trend flags a dulling tool, a step jump flags a broken one.
  • Spindle bearing & gearbox health — bearing defect frequencies and gear-mesh harmonics compared against a commissioned baseline, on machines that run around the clock.
  • Plant-wide roll-out — many machines share one RS485 / MODBUS chain and one log format; where the monitoring network is IP-based, the GHA360 adds an Ethernet triaxial channel of the same measurement.

Key specifications

  • Measurement axis: X / Y / Z (triaxial)
  • Range: ±2 / ±4 / ±8 / ±10 / ±20 / ±40 g
  • Resolution @ 1 Hz: < 1 mg
  • Bandwidth (3 dB): 500 Hz
  • Noise density: 21 µg/√Hz (±2 g version)
  • Output rate: 5–1000 Hz settable
  • Interface: RS232 / RS485 / TTL · MODBUS RTU
  • Supply: DC 9–36 V · < 60 mA @ 12 V
  • Protection: IP67 aerospace aluminium · magnetic base
  • Housing / weight: 34.2 × 34.2 × 38.5 mm · ≤ 68 g

With a magnetic base, multi-point RS485 / MODBUS networking and a configurable range up to ±40 g, the GKG3 gives machine builders and plant operators a single, standard-interface sensor for both collision protection and condition-based tooling maintenance.